Elko eLAN-RF-003 Manuel d'instructions télécharger pdf (Page 44)

444

Article

1x...

°c

Code

DIML1840

220÷240

0,103

0,130

0,147

0,174

0,093

0,133

0,153

0,203

0,090

0,120

0,155

0,126

0,178

0,127

0,210

18 T8

25 T8

30 T8

36 T8

18 TC-L

24 TC-L

36 TC-L

40 TC-L

18 TC-F

24 TC-F

36 TC-F

24 T5

39 T5

22 FC-T5C

40 FC-T5C

22,5

0,98 10...+60 75 0,5÷1,5 340 359 29 26 1 DL118-40

DIML22440

220÷240

0,175

0,160

18 T8

18 TC-L

18 TC-F

25T8

16 0,98 10...+60

75 0,5÷1,5 340 359 29 26 1 DL224-40

0,260

0,315

30 T8

36 T8

0÷60

0,210

0,275

0,355

0,218

0,280

0,210

0,350

0,210

0,303

24 TC-L

36 TC-L

40 TC-L

24 TC-F

36 TC-F

24 T5

39 T5

22 FC-T5C

40 FC-T5C

22,5

0,98 10...+60

2x...

Accessories: Thermo valve ALPHA AA, dimmable ballast DIML

Thermo valve ALPHA AA 0–10V, ALPHA AA 230V, ALPHA AA 24V

thermo valve ALPHA AA is used to regulate heating in the RF Control and iNELS systems

- ALPHA AA 0–10V in combination with DAC units

- ALPHA AA 230V and ALPHA AA 24V with any system switching actuator

ALPHA AA 0–10 V: works in the mode of continuous regulation using control voltage of 0–10V.

The thermo-electronic functional principle meets the following requirements:

- exact regulation behaviour

- long operating life

- noise-free operation

ALPHA AA 230V and ALPHA AA 24V: work in the open/closed modes.

Main features:

- noise-free operation

- design: without voltage opened / without voltage closed

- valve position visual indicator

EAN code

Alpha AA 0-10 V 4031602004475

Alpha AA 230V, NC 4031602000286

Alpha AA 230V, NO 4031602000309

Alpha AA 24V, NC 4031602000293

Alpha AA 24V, NO 4031602000316

EAN code

DIML 1840 - 8009991027845

DIML 22440 - 8009991027913

a dimmable DIML ballast to control the brightness of  uorescent T8 tubes

(26 mm in diameter)

if the ballast is not included by the manufacturer of the light, it can be additionally

installed into it. It is also possible to make a “retro t” - i.e. to replace the equipment of

the existing standard  uorescent tube by this dimmable ballast

another indisputable bene t (along with the dimming function) is the “soft start”, which

means a slow increase of the brightness of the light, which increases the life of light sources

the dimmable ballast is controlled by a 1–10V signal

it is supplied in four designs, depending on the power of the light sources ( uorescent

tubes) in the light (see the chart below)

Technical parameters

Dimmable ballast DIML

ALPHA AA 0-10 V

Technical data

Operating voltage:

Operating input:

Input control voltage:

Settings:

Protection:

Conductor:

Mean stopping time:

Stopping force:

Cable length:

Color:

Dimensions h/w/d:

24 V DC or 24 V AC 50/60 Hz

1.5W / 300mA for 2 min. at max.

0 - 10 V DC

4 mm

IP 54/II

3 x 0.22 mm

30 s/mm

100 N ±5 %

1 m

white RAL 9003

60.5+4 x 44 x 64 mm

230 V, 50/60 Hz

1.8W / 300mA for 2 min. at max.

4 mm

IP 54/II

2 x 0.75 mm

100 N ±5 %

1 m

white RAL 9003

55+5 x 44 x 61 mm

24 V AC, 50/60 Hz

1.8W / 250mA for 2 min. at max.

4 mm

IP 54/II

2 x 0.75 mm

100 N ±5 %

1 m

white RAL 9003

55+5 x 44 x 61 mm

ALPHA AA 230 V ALPHA AA 24 V

the thermo electric valve ALPHA AA is intended for zone or individual regulation

with high di erential pressures for all thermostatic valves.

regulating thermostatic valves of  oor, radiator and convector heating.

ALPHA AA 0–10V with built-in electronics for continuous (proportional) control

of thermostatic valves

Beneﬁ ts:

- continuous (proportional) lift

- suitable for fast heating

Use:

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Commentaires sur ces manuels

Pas de commentaire

Elko eLAN-RF-003 Manuel d'instructions Page 44

Commentaires sur ces manuels